Methods for Covering Exposed Plywood Edges

Building a woodworking project with plywood typically requires that the builder uses a method for covering the exposed edges of the plywood. Plywood is made from a series of laminated strips with the wood grain on subsequent layers oriented in a perpendicular manner to each previous layer. The layers are pressed into place and secured using a special type of woodworking glue.

While the alternating layers of strips make plywood a very stable material ideal for building tables, cabinets, and utility shelves, leaving the edges of the plywood uncovered can detract from the overall look of the piece. Following are four methods for covering the edges, to give the plywood a finished look.

50 Free Woodworking Plans

Edge Banding

Your home center or hardware store typically sells laminated edge banding that can be glued to the edges of the plywood. This banding is probably the most common method of covering curved cuts in plywood, as the banding is flexible enough to adhere to all but the tightest curves. Since heat is needed to melt the glue and attach the edge banding, use an old flat iron or a specially-designed heat gun for melting the glue before positioning the edge banding.

As the glue sets, use a firm roller to remove any bubbles and secure the edge banding to the plywood. After the glue has dried, a scraper or utility knife can be used to remove any excess glue or trim the edges of the edge banding flush with the faces of the plywood for a clean, finished look.

Screen Molding

Most home centers or lumber yards sell screen molding that is available in widths that match the thickness of plywood. Screen molding can be tacked into place on the edge of plywood using a brad nailer before sanding the edges so that the plywood and screen molding transition is smooth and even. Use a wood filler to fill the nail holes before applying any paint finish or stain.

Tip: If you have any junctions where two pieces of screen molding will butt into one another, use a miter saw to cut angles into the ends of the screen molding rather than putting them into one another.

Tongue and Groove

A common method for applying an edge treatment is to apply a piece of hardwood stock to the edge that either matches the plywood or compliments the plywood to create a contrasting look. A groove can be cut into either the plywood or the hardwood edging, and then a corresponding tongue can be cut out of the opposite material. The tongue should be centered and one-third of the thickness of the plywood.

For instance, if you’re using 3/4-inch plywood and applying a 3/4-inch thick banding, cut a 1/4-inch wide groove in the center of one of the adjoining pieces, followed by fashioning the corresponding tongue out of the matching material. A table saw with a stacked dado blade set or a router with the appropriate bits are probably the two most common methods for creating this tongue and groove joint.

Once the tongue and groove are cut, dry fit the two together to check the fit before applying glue and affixing the hardwood to the plywood edge. Use clamps to hold the joint together until the glue dries.

Biscuit Joinery

Another method for attaching hardwood edges to plywood is to use biscuit joinery. This involves aligning the hardwood with the plywood and cutting matching slots into both pieces using a biscuit joiner (also known as a plate joiner). Align the hardwood with the plywood and make a pencil mark across the joint onto both pieces roughly every eight inches along the joint to denote the locations for cutting biscuits. Then, adjust the height of the blade on the biscuit joiner so that the slot will be centered within the joint, and cut a slot at each pencil location on both faces of the joint.

Once the slots are all cut, place a thin layer of glue into the slots and insert a matching biscuit into each of the glued slots on one of the two faces. Then align the biscuits with the glued slots in the other edge of the joint and press the biscuits into the slots, aligning the hardwood with the plywood edge. Use clamps to hold the joint in place until the glue dries, then sand the faces to ensure that the transition between the plywood and the hardwood is smooth and even.


Leave a Reply

Your email address will not be published. Required fields are marked *